Welcome to 911UK
The only place for Porsche, 911uk is the definitive enthusiast and resource site for the Porsche 911.
Registration is fast, simple and absolutely free, so join up today for full access to the site and benefit from latest member offers.

Porsche Classifieds
Sell Your Porsche on 911uk
Create a Free Classified Advert
Search Ads
Classified Adverts FAQ
Trade Classified Information
Buyer & Seller Fraud Protection
Consumer Rights Act
Pre Purchase Inspection (PPI)
Porsche Car Sourcing
Porsche Cars Wanted
Official Porsche Centre Reviews
Model
Stock
Porsche 911
992 : 2019- 0
991 : 2011- 24
997 : 2004- 65
996 : 1997-2005 32
993 : 1993-1998 4
964 : 1989-1993 2
Carrera 3.2 : 1983-1989 2
Carrera SC : 1977-1983 2
930 Turbo : 1975-1989 1
Early 911 : 1964-1977 1
Porsche Other Models
Classic : 1950-1965 0
Boxster : 1997- 31
Cayman : 2005- 21
Cayenne : 2003- 6
Macan : 2014- 6
Panamera : 2009- 0
912-914-924-928-944-968 1
959 - CarreraGT - RaceCar 0
Car Parts For Sale & Wanted
Other Items For Sale & Wanted
Wheels Tyres For Sale & Wanted
Number Plates For Sale Wanted

Porsche Services
Porsche Body Shop Repair
Paint Protection & Wrapping
Porsche Classic Insurance
Porsche Classic Parts
Porsche Classic Restoration
Porsche Design Collection
Porsche Engine Gearbox Rebuild
Porsche Heritage & History
Porsche News
Porsche Picture Gallery
Win a New Porsche 911

Porsche Parts
Body Parts, Body Styling
Brakes, Clearance
Electrical, Exhausts
Engine Cooling, Engine Electrical
Engine Rebuild, Heating Cooling
Interior Incar, Lighting
Rubber Seals, Service Parts
Steering, Suspension
Transmission, Workshop Tools
Early 911, 911 - 930, 928 - 968
964 - 993, 996 - 997, Boxster
Cayman, Cayenne, Panamera

Porsche Model Range
911 [992] 2018-Current
Porsche 911 [992]
911 [991] 2011-2019
Porsche 911 [991]
911 [997] 2004-2012
Porsche 911 [997]
911 [GT] GT1-GT2-GT3
Porsche 911 [GT]
911 [996] 1997-2005
Porsche 911 [996]
911 [993] 1993-1998
Porsche 911 [993]
911 [RS] RS-RSR
Porsche 911 [RS]
911 [964] 1989-1993
Porsche 911 [964]
911 3.2 1983-1989
Porsche 911 3.2 Carrera
911 SC 1977-1983
Porsche 911 SC
911 [Early] 1964-1977
Porsche 911 [Early]
Boxster & Cayman
Porsche Boxster & Cayman
Cayenne & Panamera
Porsche Cayenne & Panamera

911uk Site Partners

Post new topic   Reply to topic
Author Message
steveoz
Monza


Joined: 21 Mar 2011
Posts: 162



PostPosted: Tue Mar 22, 2011 10:09 am    Post subject: 996: Replacing Variocam 'Lids' or flanges N/S Reply with quote

A quick how to that might help someone....

This is for the nearside, I will add offside as soon as I get chance. I popped into the garage this evening and did a quick few bits on the nearside before having to go out and managed to do this in aprox 15 minutes, I would say that if you budget 20 minutes for the nearside that is plenty.

First, Jack the car up using the jacking point at the passenger side rear. I'm sure I don't need to tell anyone to support with axel stands as well.

Next remove the wheel.

From here you can see the variocam housing:



You'll notice the small block in the picture to the left of the variocam housing that I am holding, this is where the connector sits for the solenoid. I've already separated here, but all you need to do, is to pull the block towards the front of the car so it pops out of the plastic clip, and then press on the connector to release the clip for removing the solenoid end of the connector:



Pull the connector free:



Next, using a 10mm socket, undo the two m10 bolts holding the flange over the solenoid, remove bolts and apply pressure with fingers to twist the flange to break the seal:



Remove flange carefully over the solenoid connector:



Check solenoid housing is lubricated and the solenoid shows no signs of moisture / water ingress. If the solenoid is damaged, replace the old seal and seek advice from an OPC, if the solenoid has fresh oil around it and is in good condition then continue. (The reason for this is that once the flange is pressed over the solenoid casing it will render the seal near useless if you remove it and you have effectively wasted a seal) - thanks to the techs at Dick Lovett for this pointer on what to look out for.



Old vs new, it's hard to tell from this picture, but the in built rubber seal on the old one is nearly no-existent compared to the new:



Apply a small amount of grease to the inside of the flange and slide new flange over connector and into place, a small amount of pressure will be required to bed the seal onto the solenoid housing (no sealing compound is required although shown on parts list).



Grease threads and replace bolts, then re-route wire and reconnect:



Push back onto retaining clip near the AOS bellow:



All done, nice new clean and well sealed variocam solenoid flange:



This really is a very quick and easy procedure, and for the sake of £12.00 per flange, it is well worth doing.

I hope this is of use to someone.


Thanks,


Steve
 
  
View user's profile Send private message
   
Display posts from previous:   
Post new topic   Reply to topic   All times are GMT - 12 Hours
Page 1 of 1

 
Jump to:  

You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot vote in polls in this forum
You cannot attach files in this forum
You cannot download files in this forum
You cannot post calendar events in this forum